Great water pump. Amazon is a great co. to work with and the Acquaer water pump is well built and works great. If I ever need another one it will be Acquaer. The pump was right on time, everything was great. you can't beat the quality of the product or the price.

My house pump went out and I was rushing to find a replacement. These were prime so I pulled the trigger. Connection was easy. Pump is extremely quiet and much more powerful than the pump it replaced. It runs smooth and is efficient. I purchased a second unit to keep as a backup that I have stored in my pumphouse This is a great pump and has been flawless for a few months. If it dies in the next year, I’ll update this review. But for the price this unit is very well built and so quiet. Can not hear it running from the house (75’)

The 3/4" line runs 50' in lake then 25' uphill and into cottage. TIPS: Throw away the rubber gasket that came with pump, and just use a tube of "gasket maker" on each piece to be connected on front of pump, wait two minutes before assembly, then tighten the two bolts. SECOND , in order to prime the pump, the 1 1/4" plug in top of pump is where you must pour water in to prime it. You must install a check valve a short way from the pump. The small hole is on top of pump is an air bleeder. You CAN NOT PRIME PUMP USING SMALL HOLE. At the bottom of the hill, I cut the 3/4" pex line and added a tee, and a gate valve with a female hose adapter. By connecting a hose I was able to fill the entire line with water before priming the pump. I ran a dedicated 110 volt line from panel box. The pump should be on its own 20 amp breaker. It runs fine on 110, but it would be better to run a 240. Last thing, the pump is wired for 110, but if you use 110 there is a little switch you move to 110, it comes set for 220. The cut in pressure is 20lbs, cut out pressure is 40, so the air tank needs to be pumped up to 18lbs. The pump works fine, great value for the money. I also purchased a separate kit with pressure gauge, relief valve and tee for connections to pressure tank. I made the job easy. I started by using 8 large cinder blocks stacked 4 wide and two high for a platform. Five stars for the pump!!!!

Our 1 hp well pump went belly up.& For the Price this appeared to be the best bang per buck. The pump is 1/2 hp and the install wen surprisingly easy. Having the ejector in the package is a plus. there is not pressure gauge nor is a foot valve in the package you need to buy those and have then ready. So far it seem to be working great. I will update this review in a month.

1. The most pressure I could get out of the pump (while holding the switch contacts closed) was 15-20 psi pumping from a water tank at ground level. 2. The attached pressure switch is useless, it does nothing but cycle on/off/on/off rapidly. No amount of adjusting it would bring it back to normal behavior. I think part of the problem is the plastic tube which goes from the switch base over to the pump casing was installed completely kinked, so pressure temporarily passes through it then it folds back on itself. Also the switch base is proprietary with the hose nipple built in, you can't buy a standard switch to put on it without re-doing the link hose and adaptors. 3. The switch wasn't even close to being adjusted into a 30/50 pressure switching behavior. 4. As other reviews have stated, the thin rubber gasket used under the shallow well adapter nose is very difficult to get to stay in place and seal well. I managed it the 2nd time around because I was careful and took great efforts. Returning.

Hard to find a pump of this quality for this price. Very satisfied with its performance on a deep well installation.

Bought this pump to draw water from a canal to run yard irrigation. Installed the pump on a dock with 1-1/4” pvc drop pipe and foot valve in the canal, drawing water from 1-3’ below dock, depending on tide height. Foot valve is positioned off the bottom of the canal, with total drop pipe length of about 8’ total vertical drop from pump elevation to pipe opening and foot valve. Pump outlet goes into a 1” discharge pvc with a manifold connected to 3 faucets to hook up hoses approximately at the same level as the pump. I will eventually instal permanent in-ground irrigation system, but, for now, I’m dragging 5/8” gardening hoses connected to spike-type impact (Rain Bird) heads. Pump instal was easy. I mounted the pump to a stand attached to my dock, switched motor to 115 v setting, and filled impeller assembly with water. Pump quickly primed and pumped water directly after plugging in the power cord. I did have to adjust the cutout pressure side of the switch to prevent continuous short cycling as pump is apparently shipped with cutout at about 40 psi. Once done, the pump will keep up with the 3 spikes at about 42 psi, according to the installed pressure gauge. I checked the specs on the impact heads, and each is rated at 3.1 gpm @ 45 psi for a total of 9.3 gpm running all three heads. I added a fourth head, but pressure drops to less than 20 psi, and that is too low to make all 4 impact heads cycle properly and throw distance of water also drops significantly. I then checked gpm output of the pump using a 5 gal bucket with no heads attached (that is, I opened all three faucets directly into the bucket, timed fill rate and divided accordingly to produce the gpm). Three separate tests worked out to calculate a gpm rate for the pump at about 10 gpm with full open faucets and about 15-20 psi. Closing the faucets slightly will increase pressures, but drops gpm to about 9 gpm at 40 psi. Bottom line: this is an inexpensive pump that will work for small irrigation projects, but don’t expect it to meet the expectations for gpm published with the pump. Specs list hourly output at 1,200 gals, which converts to 20 gpm assuming 1,200/60 mins = 20 gpm. Truth is , actual gpm is about half of published rate. The pump seems to run fine otherwise and is only moderately loud as pumps go. As I get to the irrigation installation, I will use sprinkler heads suited to “dirty water” with interchangeable nozzles to accommodate reduced gpm of the pump.

Installation facile, bonne suction et poussée. Je l'utilise pour arroser ma haie de cèdre 2h à tout les jours depuis 3 mois déjà et elle fonctionne très bien! Ma pointe est située 30 pieds plus bas dans un cours d'eau et je n'ai aucune difficulté. Vient avec la pointe et les accessoires pour l'installer en simple ou double tuyau.

So far so good! Better design at all levels, it even comes with cable and plug! It needs a third mounting point/bolt for over the tank installation.