So this seat comes with NO INSTRUCTIONS. Here's how to install quickly and easily. It can make the difference of loving or hating this seat.Turn the hinge anchor covers to the unlock position (left). Push the long plastic bolts (phillips head first) into bottom side of hinge. They snap in. They don't screw in. Then turn the anchor covers to the lock position, locking in the plastic bolts and giving your seat some fangs.Place seat on toilet, pushing bolts through toilet's seat mounting holes.Take the little black plastic nuts, broad end first, and screw onto long plastic bolts from the bottom. Make as hand tight to toilet as possible. Broad end first makes the nut wing easier to grip from the bottom, as it goes on either way.Note: It can be hard to screw nuts on all the way for lack of finger space. Don't be afraid to trim the wing of the nut a little with a scissors if needed. This is necessary for my Kohler toilet. Then just screw it on as far and tight as you can.Now that the seat's on, you can use the quick-release feature to tighen it down harder. Turn both hinge anchor covers to the unlock position. Now pull the entire seat off the toilet. The seat comes off and the plastic bolts stay, exposing the phillips heads.Tighten them down hard with a phillips screwdriver while holding the black nuts below. Carefully place toilet seat back over bolts until seated securely. Turn covers to lock position and make sure all is tight.And there you go! It's on and it can be pulled on and off til your hearts' content without unscrewing.Note: The caps of the hinge anchor covers do NOT pry up and open. They look like they should, but don't. Down the road, it's easy to forget you can't flip those covers up to expose the phillips head for tightening. They can break off if you try. You have to pull the whole seat off to get to the bolts for tightening. Tip: Whenever you pull seat off to clean, have a screwdriver handy and tighten down harder if necessary.Confession: I used to hate this toilet seat and vowed never to buy one again. I installed my old one (same exact Bemis seat) years ago and completely forgot it even had a quick change feature. When it started to wiggle, I'd grudgingly get on the floor and tighten those annoying black plastic nuts from the bottom as I could, but couldn't get them much tighter. It would come loose again soon. I hadn't trimmed the wing edge at all so the wing hit the toilet and would get stuck. I swore my next seat would have a stay-tight feature, or metal hardware I could clamp down hard with a ratchet. I couldn't find a seat on Amazon the right size, color, and price. So I thought I'd get the same one, and order a tightening kit.I'm not convinced the seat needs a tightening kit-- or that the one sold on Amazon fits this exact seat. If you try it, please comment below. I really think tightening from the top lets you clamp it down hard enough that it shouldn't come loose very often. And it's easy to tighten when it does.I agree with many reviewers that this seat is the best value by far. Are these 1980's prices? And it's real quality, solid wood, old school. My old one never broke, and the new one is identical in every way. My old one was purchased somewhere around 2005, so it held up well. It did recently get a large chip in the finish, but something may have been dropped on it. Otherwise the finish held up well, not that anyone here pees on the seat.The seat color in the pictures is biscuit. Even though the Kohler toilet is almond. I guessed my toilet was biscuit, but you can see the biscuit is lighter. This Bemis seat does come in almond, looks like it would match, but not sure I want to bother. Kohler also has a seat in almond or biscuit. Pictures are lined up at the bottom, as the posting process would not allow them to be posted appropriately throughout the review.

Good sturdy wood seat not cheaply made. Cleans easily

High quality. Install was very easy. I expect a long life being a Bemis.

I’m giving it a 4 star but really because the description was misleading. According to the pictures, I should have gotten a biscuit for Kohler, but in actuality I should have gone with almond.They are very similar and only I can tell the difference and it’s in a bathroom only I use.It was super fast and easy to install. Comes off easy for cleaning the hard to reach spots. It sits with no wobble and is high quality, stable material. It looks great even if the shade is a bit lighter than I needed.It also fit very easy over my bidet.

Great product for under $20. Sturdy, easy to install.

This was the perfect color for replacement of our old lid. This color is so hard to find.

Color matched toilet perfectly....and new design is sharper and nicer than the old one from Blevins we're replacing. That said....manufacturing is not as good. Finish has a number of white spots where the color bubbled. We're not returning it since we really need it and it's in the guest bath. If it was a primary bath....we'd return for replacement.

Have had to readjust it a few times because one side lets loose. Has these clips you turn for easy installation but one of them keeps loosening causing the toilet seat to move. It’s easy to readjust but I have never had to readjust a toilet seat so frequently. It is a good quality toilet seat itself I just wish the way it is attached to the toilet was more secure.

The quality of this seat seems great. However, the measurement of the hinges to the toilet bowl were off and there is no flexibility. I think this will be the case for most older toilet bowls. We couldn’t fit this on ours and had to return.

Solid, but heavy

Well packed. Quality toilet seat.

Excellent product just not suitable for uk fittings. Not adjustable. Shame

Sehr teuer! Er lässt sich aber leicht zum Reinigen abnehmen.